https://www.lifetimeledlights.com/
Willys MB build
« previous next »
Pages: 1 ... 5 6 [7] 8 9   Go Down

Author Topic: Willys MB build  (Read 57789 times)

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #90 on: March 13, 2016, 02:19:08 PM »
Rolled it outside to blow off the dust and metal shavings and clean up the shop a little

Snapped a few teasers:



Logged

Offline s0l0ithz

  • Sr. Member
  • ****
  • Posts: 483
Re: Willys MB build
« Reply #91 on: March 13, 2016, 10:26:01 PM »
Does the Steering tilt in this thing?
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #92 on: March 14, 2016, 08:02:37 AM »
Quote from: s0l0ithz on March 13, 2016, 10:26:01 PM
Does the steering tilt in this thing?

Yes, tilt column and removable wheel.  ;D
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #93 on: March 21, 2016, 08:00:35 PM »
Gussets and tabs



Inner fender and side tins

Logged

OffRad

  • Guest
Re: Willys MB build
« Reply #94 on: March 21, 2016, 09:32:37 PM »
nice ride
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #95 on: March 23, 2016, 08:59:08 AM »
Logged

Offline s0l0ithz

  • Sr. Member
  • ****
  • Posts: 483
Re: Willys MB build
« Reply #96 on: March 24, 2016, 01:23:36 PM »
Mark this is looking great
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #97 on: March 24, 2016, 09:29:45 PM »
ECM returned after being reprogrammed by LT1swap.com

Fuel plumbing supplies ordered

Harnesses arrived too
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #98 on: April 02, 2016, 08:01:14 AM »
one front fender completed




rear axle shafts arrived today
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #99 on: April 05, 2016, 07:01:25 PM »
Now with matching driver side.  It is officially a "flat fender" now.
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #100 on: April 08, 2016, 04:13:00 PM »
Cowl done


Time to move on to other little details
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #101 on: April 09, 2016, 06:14:06 PM »
Rolled it out of the shop again to clean before beginning accel pedal modifications



Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #102 on: April 11, 2016, 08:37:21 PM »
Accel pedal mounted

Wiring harness pinout started
Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #103 on: April 13, 2016, 08:14:27 PM »
Doesn't this look FUN?!  Pin-out on the ECM...

Logged

Offline Wingman

  • Administrator
  • Hero Member
  • *****
  • Posts: 1980
Re: Willys MB build
« Reply #104 on: April 20, 2016, 08:06:20 PM »
Harness nearly done.  Relay pack needs to be assembled.
Logged
Pages: 1 ... 5 6 [7] 8 9   Go Up
« previous next »
 
©Team Mudnuts 4x4 Club, Inc. DBA Fingerlakes 4x4 All materials on this site may not be reproduced without permission.

XOOPS Template created with IXThemes

test block /modules/smf/index.php?topic=3415.90